icnd2 Exam Questions For Cisco 200-105

DumpsSchool Cisco 200-105 exam dumps have authentic information to attempt all questions in the real exam. This exam material enables you to get verified knowledge of LAN switching technologies, IPv4 and IPv6 routing technologies to succeed in the 200-105 exam.

Try it Latest DumpsSchool 200-105 Exam dumps. Buy Full File here: https://www.dumpsschool.com/200-105-exam-dumps.html (691 As Dumps)

Download the DumpsSchool 200-105 braindumps from Google Drive: https://drive.google.com/file/d/1TwCxP9R2WPXn5O77CUBND73niqczpZDp/view (FREE VERSION!!!)

Question No. 1

Refer to the graphic. Users on the Holyoke router are unable to access the intranet server attached to interface

E0 of the Chicopee router. Inspection of the routing table of the Holyoke router shows that an entry for the

Chicopee E0 network is missing.

Which command will configure the Holyoke router with a path to the intranet server network?

Answer: E

Question No. 2

Workstation A has been assigned an IP address of 192.0.2.24/28. Workstation B has been assigned an IP address of 192.0.2.100/28. The two workstations are connected with a straight-through cable. Attempts to ping between the hosts are unsuccessful.

What are two things that could be attempted that would allow communications between the hosts? (Choose two.)

Answer: A, B

Question No. 3

Which of the following HSRP router states does an active router enter when it is preempted by a higher priority

router?

Answer: B

Question No. 4

Which option describes a difference between EIGRP for IPv4 and IPv6?

Answer: B

Router ID – Both EIGRP for IPv4 and EIGRP for IPv6 use a 32-bit number for the EIGRP router ID. The 32-bit router ID is represented in dotted-decimal notation and is commonly referred to as an IPv4 address. If the EIGRP for IPv6 router has not been configured with an IPv4 address, the eigrp router-id command must be used to configure a 32-bit router ID. The process for determining the router ID is the same for both EIGRP for IPv4 and IPv6.

Question No. 5

Refer to the exhibit. The router has been configured with these commands:

What are the two results of this configuration? (Choose two.)

Answer: D, E

Question No. 6

Which two options are valid WAN connectivity methods? (Choose two.)

Answer: A, C

On each WAN connection, data is encapsulated into frames before it

crosses the WAN link. The following are typical WAN protocols:

1. High-level Data Link Control (HDLC): The Cisco default encapsulation type on

point-to-point connections, dedicated links, and circuit-switches connections.

2. PPP: Provides router-to-router and host-to-network connections over synchronous and

asynchronous circuits. PPP was designed to work with several network layer protocols,

including IP.

3. Frame-relay: A successor to X.25. This protocol is an industry-standard, switches

data-link layer protocol that handles multiple virtual circuits

http://en.wikipedia.org/wiki/Wide_area_network

Question No. 8

Which two options are primary responsibilities of the APIC-EM controller? (Choose two)

Answer: D, E

Question No. 9

Which two statements are characteristics of a distance vector routing protocol? (Choose two.)

Answer: B, E

Question No. 10

Which command do you enter to create an SVI?

Answer: A

Question No. 11

Which IEEE standard does PVST+ use to tunnel information?

Answer: B

Question No. 12

Which switch architecture is scalable, flexible, resilient, and relatively inexpensive?

Answer: C

Question No. 13

Which component of VPN technology ensures that data is unaltered between the sender and recipient?

Answer: D

Question No. 14

Which command do you enter to determine whether LACP is in use on a device?

Answer: B

200-105 Dumps Google Drive: (Limited Version!!!)
https://drive.google.com/file/d/1TwCxP9R2WPXn5O77CUBND73niqczpZDp/view

Related Certification: CCNA Routing & Switching dumps